Secure Online Shopping
1M Dive Towers
3M Dive Towers
Aluminum Diving Boards
Cross-Braced Pool Ladders
Duradapt Dive Towers
Durafirm Dive Stands
Duraflex Diving Boards
Fiberglass Diving Boards
Grab Bars
Grab Rails
Guard Chairs-Economy
Guard Chairs-Griffs
Guard Chairs-Permanent
Guard Chairs-Portable
Guard Chairs-Recycled
Handrail Accessories
Observation Windows
Pool Ladder Parts
Raft/Dock Ladders
Recessed Steps
Replacement Guard Chair Seats
S R Smith Dive Towers
Stair Rails
Standard Pool Ladders
Starting Platforms
Starting Platforms Options & Accessories
Underwater Platforms
Underwater Treadmills
Keeping Your Stainless Steel Pool
Equipment Rust-Free.
|
S. R. Smith Dive Towers
 |
S. R. Smith Diving Towers
S.R. Smith diving towers feature the highest level of design
fabrication strength to meet ANSI standards. When properly
installed and equipped, these dive towers will meet or exceed the
standards set by FINA, NCAA and U S Diving governing bodies. Both
1-meter and 3-meter dive towers are available in four
configurations; left-mount, right-mount, heel (rear)-mount
and the dual-mount.
Front Post Assembly - 10" schedule 20 carbon steel pipe
15 degrees and welded to a 5/8" top plate and a 3/4" bottom plate.
Ladder Assembly - two 1.90" O.D. x .145" wall 304 stainless
steel welded mirror finish ladder posts with 1 5/8" O.D. x .065" wall
stainless steel tube handrails. The 1 meter stands have two 6" wide
non-slip, stainless steel treads, the 3 meter stands have 9 treads.
Tray Assembly - 3/16" carbon steel plate formed and reinforced
using 3/8" plates. The tray will accept any mounting configuration.
Jig Assembly - Smaller jig designed for easier installation on
all units except for heel mount units. Six 1" bolts with reinforcing
rods hold the 3/4" flange plate into the concrete. Jigs are also
provided for the ladder assembly and the heel mount post (side mount
towers only).
Quick Adjustable Fulcrum - heavy duty design with brass gears
and tracks. The rear ratchet assembly is machined from high quality
stainless steel pipe. Ratchet handle allows for ease in adjusting
forward or backward movement of the fulcrum.
Tie-Down Assembly - mounted in neoprene blocks that are secured
to the tray by 3/16" diameter straps bolted in place. The board is
bolted to a 5/16" x 2 1/2" x 2 1/2" steel angle welded to a 1" diameter
bar. The tie-down assembly acts as a hinge to tilt the board up on the
1-meter tower. The board is held up with a T-bar that is placed in a
socket on the tray.
Handrails - the handrails are 36" above the board and extend at
least to the edge of the pool. Made of 1.90" O.D. x .065" wall 304
stainless steel welded mirror finish tubing. |
|
Item #42-093 |
1-Meter Dual Mount Dive Tower
Shipping Weight: 965 lbs. |
$11,891.88 |
 |
|
Item #42-092 |
1-Meter Heel Mount Dive Tower
Shipping Weight: 942 lbs. |
$9,566.37 |
|
|
Item #42-091 |
1-Meter Left Mount Dive Tower
Shipping Weight: 867 lbs. |
$10,234.62 |
|
|
Item #42-090 |
1-Meter Right Mount Dive Tower
Shipping Weight: 867 lbs. |
$10,234.62 |
|
|
Item #42-097 |
3-Meter Dual Mount Dive Tower
Shipping Weight: 1,280 lbs. |
$17,888.31 |
|
|
Item #42-096 |
3-Meter Heel Mount Dive Tower
Shipping Weight: 1,220 lbs. |
$12,601.71 |
|
|
Item #42-095 |
3-Meter Left Mount Dive Tower
Shipping Weight: 1,135 lbs. |
$13,592.21 |
|
|
Item #42-094 |
3-Meter Right Mount Dive Tower
Shipping Weight: 1,135 lbs. |
$13,592.21 |
|
|
The diving equipment shown here should be used
only on pools that conform to FINA, NCAA, NFSHSA or US diving
standards. Please refer to your local, municipal and state statutes,
ordinances, rules and regulations which may vary. |
|
